Waterproofing Integrity utilise a number of types of electronic leak detection with a view to being fit for purpose and benefits that each offers. Electronic Leak Detection is a testing method applied to many waterpoofing membranes as a method of checking for the continuity of the membrane. The thickness readings are obtained by measuring the time taken for the ultrasonic signal to propagate from the probe to the coating/substrate interface and back. Making QUALITY products was and still is our priority and continually Investing in the backbone of our company. While Durotech has its own testing laboratory, the Durotech range has also been externally tested as low VOC by an independent, nationally accredited Firm. At Durotech we make it our mission is to be at the front when choosing construction chemical products and solution
The short answer is that there is no simple, general relationship between laboratory and accelerated weathering testing. Most weathering testing, at least to begin with, is quality control testing – short, defined screening tests for fixed time intervals that generate pass/fail results. Weathering testing has resulted in drastic increases in the lifetime of many important product
Q-Lab can help you determine the best comprehensive test plan for your products and materials. These two test types are complementary and, performed together, make up a complete weathering test program. Water can be present in the form of dew (condensation), relative humidity, and rainfall. Water can also cause physical effects like erosion, absorption, freeze/thaw stress, thermal shock, and material loss from impact. Browse our weathering industries pages and case studies for examples of weathering durability testing, or check out this general testing guid
Dunlop Pro Rapid Tape is a self-adhesive sealing tape that provides a waterproofing seal between the surface joints of the… A self-adhesive waterproofing joint tape provides a seal between the surface joints of the floor and wall, under shower grates and… • Dries to a keyed finish to promote direct tile adhesion – suitable for use in conjunction with all cement based tile adhesives that conform to AS2358.
Dunlop Timber Joint Seala
How Inspect365 Works to Give You Peace of Mind A Simple 5-Step Inspection Process
Whether prior to remedial waterproofing works being undertaken to determine scope or following completion, Waterproofing Integrity can provide confidence of issues being effectively addressed. Our team of technicians can come to your project to check on the compliance of your waterproofing installation.
About ITA
AS 4654 is the primary Australian standard that relates to the physical performance properties of waterproofing membranes specified for use… Tensile strength testing is a fundamental method for characterising the mechanical properties of waterproofing membranes, coatings, and other materials and… AS/NZS 4858 is the primary Australian standard that relates to the physical performance properties of waterproofing membranes specified for use… Wasting water along with time delays involved with flood testing in areas that are large and deep (as walls can leak as much as floors, joints and penetrations under hydrostatic pressure) Waterproofing Membranes for Wet Areas is no longer viable nor acceptable. Electronic Leak Detection [ELD testing] is fast becoming the preferred testing method for builders, waterproof manufacturers and waterproofing contractors who understand time is money on a building sit
Our Tools: IntegriScan
The low voltage Vertical Surface Scanning roller listed under the guide for testing vertical substrates works by moistening the roller sleeve as the operator rolls the testing tool up the substrate forcing the water before it into any breaches. In areas where there are multiple breaches, further testing needs to be undertaken each time until no more breaches are identified. If there are only puddles on the surface, then the circuit would be incomplete resulting in missed breache
ProtectSys
AS/NZS 4858 is the primary Australian standard that relates to the physical performance properties of waterproofing membranes specified for use in wet areas such as bathrooms, kitchens, laundries and wet rooms, to prevent water ingress and protect structures from moisture damage. This is best achieved during construction where direct contact with the membrane can be achieved as trying to quantify waterproofing membrane performance once it is tiled or covered has its limitations and can be more costly to repair. Get a free quote for any of our services, from waterproofing inspections to frame inspections and more. Whether it’s a bathroom, balcony, basement, or rooftop, we have the expertise to ensure that your property stands strong against potential water damage. We check that your roof is not only protecting you from the rain but also ensuring that no water is seeping into the propert
Enquire About the AS 4654.1: Waterproofing Membranes for External Above Ground Use Testing
Its extremely important to make sure that when deciding which technologies you are chosing to use on your next project that you are partnering with the right people. Independent Testing Australia (ITA) is equipped with specialised apparatus to test materials and provide data to coating manufacturers, specifiers, builders and waterproofers to determine product suitability for use in the Australian construction industry and satisfy documentation requirements of the Australian Building Code (BCA), the National Construction Code (NCC) and Australian Paint Approval Scheme specifications (APAS
Tags: Australian waterproofing membrane testing